Trailer coupler types and sizes: ball sizes, coupler styles, brands and locks

Short answer: Match the hitch ball to the size stamped on the coupler: 1-7/8, 2 or 2-5/16 inches. CURT's chart puts 1-7/8-inch balls at 2,000 to 3,500 lb, 2-inch balls at 3,500 to 12,000 lb and 2-5/16-inch balls at 6,000 to 30,000 lb, but the exact rating is on each part. The safe limit for your setup is the lowest rating among the coupler, ball, ball mount and receiver.

Step by step

  1. Read the coupler. Find the markings stamped or cast into the coupler: maker, part or model number, the ball diameter it takes and its maximum gross trailer weight rating.
  2. Match the ball diameter. Use a ball of exactly that diameter. A 2-inch ball can sit inside a 2-5/16-inch coupler and the latch may close, but the fit is loose and unsafe.
  3. Match the shank to the ball mount. The ball's shank diameter must fit the hole in the ball mount, and the shank must be long enough for the lock washer and nut. Torque the nut to the ball maker's spec.
  4. Check every rating. Compare the coupler, ball, ball mount, receiver and vehicle ratings with the loaded trailer's weight. The lowest one is your limit.
  5. Latch, pin and chain. Close the latch fully, insert the latch pin or lock, hook up the safety chains and plug in the lights before you move.

The coupler is the part on the front of the trailer tongue that fits over the hitch ball (or, on heavy trailers, a hook or kingpin). Getting the size and rating right is the first safety check on any hookup.

Ball sizes and typical ratings

CURT lists four standard ball diameters. Ratings vary by part number, so always read the rating on the ball you have.

Ball diameter Typical shank diameter Typical rating (gross trailer weight) Common use
1-7/8 in 3/4 to 1 in 2,000 to 3,500 lb Small utility, boat and jet-ski trailers
2 in 3/4 to 1-1/4 in 3,500 to 12,000 lb The most widely used size: utility, boat, camper and many car haulers
2-5/16 in 1 to 2 in 6,000 to 30,000 lb Heavier equipment, dump and travel trailers
3 in 2 in 30,000 lb Heavy commercial

Source: CURT’s ball size chart and specification sheet. CURT’s sheet also says the ball platform must be at least 3/8 inch thick, and the hole no more than 1/16 inch larger than the shank. Torque the nut to the maker’s figure; CURT lists 160 ft-lb for its 3/4-inch-shank 1-7/8-inch ball (#40016), and larger shanks use higher values.

How to read a coupler’s markings

Couplers sold for trailers up to 10,000 lb are designed and tested to SAE J684, the standard for trailer couplings, hitches and safety chains. Washington State’s rules require couplings to be classified, tested and labeled to J684, and Maryland’s rules require each coupling to be marked with:

  • the maker’s name or trademark
  • the part, model or style number, and the coupler class
  • the maximum gross trailer weight

Most couplers also show the ball diameter. Look on top of the coupler body or near the latch. If the markings have worn off, a hitch shop can identify the coupler from its shape and part number, or you can replace it.

Matching ball, shank and receiver

  1. Ball diameter = coupler size. No exceptions.
  2. Shank diameter = ball mount hole. Common holes are 3/4, 1 and 1-1/4 inches. The shank must be long enough for the lock washer and full nut.
  3. Ball mount shank = receiver size. Class I and II receivers are usually 1-1/4 inches and Class III and IV are usually 2 inches (the Trimax kit below lists pins for both). Use the correct hitch pin.
  4. Lowest rating wins. Coupler, ball, ball mount, receiver and the vehicle’s towing limit each have a rating. Stay under the smallest one.

Coupler styles

  • Straight-tongue (straight channel) couplers bolt or weld onto a single straight tube tongue, often 3 inches wide. CURT says they are among the most common types and popular on boat trailers. Lippert notes they suit lighter loads.
  • A-frame couplers fit a tongue where two rails meet in a V. They are usually rated higher than straight-tongue couplers and often have a hole for a tongue jack. CURT says they are common on enclosed, cargo and RV trailers.
  • Adjustable channel (slip collar or “C-channel”) couplers bolt into a vertical channel bracket on the tongue so the coupler can be moved up or down to level the trailer. CURT’s adjustable couplers go up to 15,000 lb; they appear on equipment and dump trailers.
  • Gooseneck couplers are a vertical tube with a ball socket that drops onto a ball mounted in a pickup bed. CURT’s gooseneck hitches are rated up to 38,000 lb.
  • Fifth-wheel pin boxes carry a kingpin that locks into a fifth-wheel hitch in the truck bed, similar to a semi coupling. CURT’s fifth-wheel hitches go up to 30,000 lb.
  • Pintle (lunette ring) couplers use a steel ring on the trailer that drops into a hook on the vehicle. CURT’s pintle hooks range from 10,000 to 60,000 lb and are used in farm, construction and military towing. Some channel couplers come in lunette ring form.

Brand and style names people search for

These are descriptions from each maker’s own pages, listed alphabetically. We do not rank or endorse any brand.

  • BULLDOG. Makes A-frame and heavy-duty couplers and round tongue jacks. Its Collar-Lok A-frame coupler (2-inch ball, 5,000 lb, Class III) uses a hinged ball socket and a collar latch. Its Wedge-Latch A-frame couplers in 2-5/16 inch go to 12,500 and 15,000 lb, and some include a “round jack hole” sized for its round top-wind jacks. “Top-wind” means the jack’s crank sits on top of the jack tube. BULLDOG’s 5,000 lb round A-frame jack has a 2.25-inch tube and 15 inches of travel. To identify one, look for the BULLDOG name and model number cast or stamped on the coupler or jack.
  • Demco. Makes EZ Latch couplers in 2-inch and 2-5/16-inch sizes for straight tube, A-frame, flat and adjustable channel mounts, from 7,000 lb up to 21,000 lb. Demco says EZ Latch couplers latch automatically when dropped on a ball and meet SAE J684 without a safety pin.
  • RAM Trailer Products. Makes adjustable channel couplers that bolt to a standard 3-inch channel, including sleeve-lock models (7,000 lb with a 2-inch ball, 12,500 lb with a 2-5/16-inch ball) and lever-latch models at 21,000 and 25,000 lb with a 2-5/16-inch ball. RAM says its couplers carry the SAE-required markings and comply with J684.
  • Sleeve-lock and slip-collar couplers (several makers) close by sliding a spring-loaded collar or sleeve, rather than flipping a latch handle. Check that the collar fully snaps forward before towing.

Coupler locks

Pick the lock by what you want to stop and by the exact coupler you have.

  • Receiver pin locks replace the plain hitch pin so the ball mount cannot be pulled from the vehicle. Master Lock says to match the pin to the size of the pin it replaces. These do not protect a parked trailer on their own.
  • Latch locks pass a locking pin through the coupler latch so the latch cannot be opened. Measure the latch hole diameter and the span you need.
  • Ball-style (plug) coupler locks put a ball or plug into the coupler’s socket and lock it there, so no hitch ball can go in. Choose the ball size that matches your coupler.
  • Universal coupler locks clamp around the coupler mouth and fit several sizes. Master Lock sells universal models for couplers up to 2-5/16 inches, and the Trimax TCP100 kit includes a coupler lock for 1-7/8, 2 and 2-5/16-inch couplers plus a latch lock and a receiver pin.
  • Model-specific locks are shaped for one coupler design. Proven Industries sells custom-fit coupler locks by coupler model, and S5 Locks sells custom-fit steel coupler locks made to fit a single coupler make or model, including BULLDOG and Demco couplers.

To match a lock: note the coupler’s maker and model number, ball size, and whether it is straight-tongue, A-frame or adjustable channel. Then check the lock maker’s fit list. Gooseneck and fifth-wheel trailers need locks made for those connections; Master Lock, for example, sells kingpin locks for fifth-wheel trailers.

Safety checks every time you hook up

  • Read the coupler size and use the matching ball.
  • Close the latch fully and check that the coupler is seated down over the ball.
  • Put a pin or lock through the latch.
  • Hook up the safety chains with enough slack to turn. See our Missouri and Kansas towing laws guide for the chain rules.
  • Connect and test the lights. See our 4-pin vs 7-pin wiring guide.
  • Look for cracks, worn latch parts or a ball that wobbles in the socket. A worn coupler should be replaced, not adjusted around.

Get it checked locally

A hitch and parts shop can match balls, mounts and locks to your coupler, and a trailer repair shop can replace a worn or cracked coupler.

Frequently asked questions

Where is the size on a trailer coupler?

Most makers stamp or label the ball size on the coupler itself, usually on top of the coupler or on the latch area, next to the weight rating. CURT notes that most manufacturers stamp or label the correct ball size on the coupler.

Can I use a 2-inch ball in a 2-5/16-inch coupler?

No. The ball diameter must match the coupler. A smaller ball can let the coupler close but leaves too much play, and the trailer can come off.

What is the difference between a coupler lock and a receiver lock?

A coupler lock blocks or encloses the coupler's ball socket so nobody can hitch the parked trailer. A receiver pin lock replaces the hitch pin so the ball mount cannot be pulled out of the vehicle's receiver. They protect different things.

Do I need a different lock for a gooseneck or fifth-wheel trailer?

Yes. A fifth-wheel trailer uses a kingpin lock, and a gooseneck coupler needs a lock made for its ball socket or latch. A bumper-pull coupler lock or receiver pin lock does not fit those connections.

Sources

  1. Standard Trailer Hitch Ball Sizes | How to Choose (CURT), accessed 2026-11-17
  2. Trailer ball specifications sheet (CURT, PDF), accessed 2026-11-17
  3. 1-7/8" Trailer Ball #40016 product specifications (CURT), accessed 2026-11-17
  4. Trailer Couplers: A-Frame, Straight-Tongue, Adjustable (CURT), accessed 2026-11-17
  5. Trailer Tongue vs. Trailer Coupler: What's the Difference? (CURT), accessed 2026-11-17
  6. Types of Trailer Hitches and Hitch Classes (CURT), accessed 2026-11-17
  7. Pintle Hooks & Mounts: Learn More (CURT), accessed 2026-11-17
  8. Understanding the Different Types of Trailer Couplers & Latches (Lippert), accessed 2026-11-17
  9. SAE J684 Trailer Couplings, Hitches and Safety Chains (ANSI Webstore listing), accessed 2026-11-17
  10. WAC 204-70-050 Coupling classification and attachment (Washington State), accessed 2026-11-17
  11. COMAR 11.13.08.07 Identification (Maryland trailer hitch regulations), accessed 2026-11-17
  12. Trailer couplers and EZ Latch compatibility (Demco), accessed 2026-11-17
  13. Collar-Lok A-Frame Coupler 028288 (BULLDOG), accessed 2026-11-17
  14. A-Frame Coupler 44125W0317, round jack hole (BULLDOG), accessed 2026-11-17
  15. Round Trailer Jack, A-Frame, Topwind 1750290301 (BULLDOG), accessed 2026-11-17
  16. Sleeve Lock Adjustable Couplers (RAM Trailer Products), accessed 2026-11-17
  17. 21K / 25K Adjustable Couplers, Lever Latch (RAM Trailer Products), accessed 2026-11-17
  18. Automotive, Towing & Trailer Hitch Locks, FAQ (Master Lock), accessed 2026-11-17
  19. Trimax coupler and receiver lock kit TCP100 (product listing, Rigid Hitch), accessed 2026-11-17
  20. Trailer Coupler Locks, Custom Fit (Proven Industries), accessed 2026-11-17
  21. The S5 Trailer Coupler Lock (S5 Locks), accessed 2026-11-17

Found an error? Email hello@hitchlistkc.com. See our editorial policy.

Find help nearby